1每班开机前必须逐点检查各润滑部分，并按期对各齿转箱、减速机补充消滑剂。

Pele o sebetsa mochini o ka sehloohong oa ho etsa li-block, karolo e 'ngoe le e' ngoe ea lubrication e hloka ho hlahlojoa ka bonngoe. Mabokose a lisebelisoa le lisebelisoa tsa phokotso li hloka ho tlatselletsa mafura ka nako, 'me li nkeloe tse ling ha ho hlokahala.

2 开机前必须检查每个感应器及行程开关是否正常.

Sensor e 'ngoe le e' ngoe le sesebelisoa sa moeli oa boemo li hloka ho hlahlojoa hore na li ka sebetsa ka mokhoa o tloaelehileng kapa che pele li sebetsa.

4条和连接螺丝是否松动，应紧固，防止振断、送料小车内是否铁块等杂物、破拱是否内动自如、固定螺丝是否松动。底模安装螺丝是否松动、锁紧度是否正确，各油管接头是否漏油、油箱电磁阀及各大小油泵是否有滴漏现象、对渗油部位应重新紧固油管。

Per shifting hlahloba haeba compaction hlooho tightening screws kapa che, haeba vibration motor screws hlephileng kapa che, haeba ketso sethaleng Trim hlobolisa ka thothometsa setaleng le ho kopanya likurufu hlephileng kapa che, haeba ho joalo tighten bona ho thibela thothomelo phoso. 'Me basebetsi ba boetse ba hloka ho hlahloba hore na ho na le litšepe tsa poleiti kapa li-sundries tse ling ka lebokoseng la ho tlatsa, haeba seqhomane sa arch se ka tsamaea ka bolokolohi kapa che, haeba li-screws tse behiloeng li hlephile kapa che, haeba hlobo e ka tlase e kenya li-screws e hlephileng kapa che, le tekanyo ea ho notlela e nepahetse kapa che. E 'ngoe le e 'ngoe ea khokahano ea oli e lutla oli kapa che, boleng ba tanka ea oli ea solenoid le lipompo tsohle tse kholo le tse nyane tsa oli lia lutla kapa che. Bakeng sa karolo ea oli e lutlang, khokahano ea oli e hloka ho tiisoa hape.

4.每班检查送板机每个板钩（俗称'鸟头）是否活动自如，检查送砖机传动链条及拖动链条的松紧度，必要时给于调整。

Ka nako e 'ngoe, hlahloba hore na hook e 'ngoe le e' ngoe ea boto (eo hangata e tsejoang e le hlooho ea nonyana) ea pallet conveyor e ka tsamaea ka bolokolohi, hlahloba tekanyo ea rekere ea koloi ea pallet conveyor 'me u hule liketane, u li fetole ha ho hlokahala.

5生产过程中不定时的巡检各运行部件、及各电器设备，做到听、闻、看，检查活动部位润滑情况及磨损情况，能做到提前预防。

Ho lekola likarolo tsohle tsa ts'ebetso le mafapha ohle a lisebelisoa tsa motlakase ka nako e sa lebelloang nakong ea tlhahiso. Ho hlahloba likarolo tsa ts'ebetso ea lubrication le ho apara boemo ka ho mamela, ho fofonela le ho sheba, e le hore ho ka thibela mochine o robehileng esale pele.

6.每班下班后必须彻底清理设备卫生，及时清理废料，保证成型机前后的清洁，以免造成混凝块，免耠成混凝嗟，

Ho tloha ka mor'a mosebetsi ho hlokahala ho hloekisa lisebelisoa ka ho feletseng, ho hloekisa likhechana ka nako ho boloka mochine o ka sehloohong o hloekisitsoe pele le ka mor'a ho sebelisoa, qoba caking ea konkreite e le hore e ama tšebeliso ea mochine.

7.设备主要零部件的润滑部位及周期.

Thepa ea lubricant housing le nako ea potoloho ea lisebelisoa tse ka sehloohong tsa thepa.